AB Prototype A-10 V2 Compensator for SIG Sauer P320 X-TEN, 10mm, Aluminum, .578"-28, Blue PVD
This is a new AB Prototype A-10 compensator for the SIG Sauer P320 X-TEN in 10mm AUTO (REQUIRES A-10 Threaded Barrel). This precision machined compensator is cut from 7075 aluminum billet and threaded .578"-28 (standard .45 thread). Works with SIG Sauer X-Ten slides with our AB Prototype A-10 threaded barrels. May work with other aftermarket 10mm slides such as the AB Prototype A-10 Slide with matching threaded barrel. WILL NOT WORK WITH BARSTO P320 10mm THREADED BARRELS. Will NOT work with X5, M17 or other 9mm/.40 full-size (4.7" or 5.0") barrels. Will require timing with included set screws and Rocksett®. Adds approximately 1.45" to the length of your slide. Should work with most X-10 holsters with open end.
PLEASE NOTE: THIS COMP IS SIZED FOR 10MM ONLY, DO NOT USE WITH 45 CALIBER BARRELS! SERIOUS INJURY AND/OR DAMAGE WILL OCCUR.
The large top port of our A-10 compensator is designed to reduce muzzle rise and felt recoil. Help tame your 10mm with this thoughtfully designed 10mm A-10 compensator. Our A-10 compensator will add a bit of style and performance to your threaded pistol. Requires correct timing, but also includes threaded set screws for additional retention. Manufactured in the USA from 7075 aluminum and hard anodized for improved wear-resistance. Thru bore is .430". Comes in black only. TUNING OF RECOIL SYSTEM MAY BE REQUIRED. We suggest X5 guide rod and 1911 government length recoil springs.
THREADED BARRELS ARE NOT LEGAL IN ALL STATES. Please be aware of state laws before ordering/installing.
Includes: 1 AB Prototype A-10 V2 Compensator (.578"-28), 10mm, Rocksett® single-use pack, set screws and Allen wrench, Blue PVD. Factory grease may be present. No other parts are included. TUNING OF RECOIL SYSTEM MAY BE REQUIRED.
Installation is available for an additional charge.
TO INSTALL:
Remove slide assembly from pistol, remove recoil spring assembly (keep barrel installed in slide). Clean threads, perform DRY-FIT before installing Rocksett®, verify fit of compensator onto barrel (compensator should bottom-out on barrel shoulder). Slightly unthread compensator to align with slide, hand tight set screws aligned to flats on A-10 barrel. Install recoil spring and reinstall slide assembly onto pistol. Cycle slide by hand and verify no interference exists with comp.
Remove slide assembly, recoil spring and compensator. Clean threads, apply Rocksett® to barrel threads ONLY (do not apply Rocksett® to set screws) following Rocksett® instructions. Install compensator until bottoming-out, then unscrews minimum amount to align set screws. Tighten set screws (removable Blue Loctite is recommended), verify compensator is properly aligned with slide. Reinstall recoil spring and reinstall slide assembly onto pistol. Verify no interference exists with comp and let Rocksett® cure following manufacturer's recommendations.
All AB Prototype manufactured products offer a limited 1-year warranty to the original purchaser covering defects in material or workmanship and only extend to replacement parts as originally provided and/or installed for the original purchaser. Warranty does not cover normal wear and tear or coatings. Any unauthorized work, installation, improper or unsafe handling or utilizing non-SAAMI, hand-loaded, reloaded and/or remanufactured ammunition will immediately void this warranty. No other warranties are given or implied.
COATING DISCLAIMER: Hard Anodize coating is tough, but may show wear from use. Hot gases, unburnt powder, etc. will wear coatings. Expect cosmetic wear. This will not affect function.
DISCLAIMER: AB PROTOTYPE IS NOT AFFILIATED WITH SIG SAUER®.
You can find our 10mm barrels here: A-10 10MM BARRELS
